Finally, select either ‘ Create Sensor‘ or ‘ Create Actuator‘. The EIS type is set automatically, but can be changed manually. In ‘ Name‘, enter the desired name for the push-button. The line in yellow highlights the last switch operated with a group address. In ‘Learn Mode’ you can select the desired group address. Do this, then select ‘Learn’ in the EIB window, not ‘Monitor’! You can then quickly and easily insert group addresses for your EIB actuators and sensors. To use the EIB Learn Mode, you must first enable the EIB monitor. To make this possible the following settings must be set in the ETS Connection Manager.Ĭlicking on the EIB Search function lists all devices that are configured in the EIB installation. The Miniserver is automatically detected by ETS as a gateway. The Loxone Miniserver acts as a full IP gateway which enables you, for example, to program with ETS directly on the local network. GENERALįor the KNX bus a separate and product specific power supply needs to be used (the KNX/EIB power supply).įor addressing and configuration of the sensors/actuators a full ETS programming software license is required. The number needed depends on the size of the rest of the program. In addition, NAT Mode must be activated in ETS.Īn accurate number of required EIB sensors/actuators will vary. In order to program KNX devices remotely, the following port must be forwarded to the Miniserver: EIB function blocks in the Configuration Software.I will be grateful for whatever assistance can be offered. My WAF is extraordinarily low (wife acceptance factor). If anyone has any suggestions based on what I have posted or the name of a good KNX installer, please advise. My wife and kids just can't wait for me to resolve the problems. Does anybody have a knowledgeable KNX guru that I can hire to get me over the finish line? Ordinarily, I would struggle until the problem was located. EtS5 is set up on a Windows PC with remote desktop connection. I have tried to find someone in the United States but KNX is really unknown here. I really need professional help (the KNX type). We have lived in our house for almost 9 months and we still can't turn on our lights. I know that there are small mistakes being made but without the experience, I don't know where. I terribly frustrated and feel a bit overwhelmed. I have just accepted that the miniserver won't connect until ETS5 is properly configured. If I have the POE IP interface, do I still need a separate power supply? Also, the KNX light on the IP interface does not illuminate.Īs far as the miniserver, I have not been able to connect to it through ETS5. It is POE and I have it connected to a Ubiquiti POE switch. Unfortunately, no.įrom the miniserver, KNX enters the IP interface by a twisted pair of Cat 6. Recently, in my never ending pursuit of KNX functionality, I purchased a N000401 from EIBMarkt I thought that maybe with an IP interface, my problems would be resolved. My miniserver is v1 and it is located in our lower level. I will provide an update on my hardware as requested. I didn't receive notification that anyone had responded to my posts. Checkout their KNX Powersupplys ( ) and IP Interfaces IP routers ( ) So for a serious KNX installation i would suggest to buy a additional KNX IP Interface / Router.Ī KNX brand where you get a good bang for the buck is for example MDT. A normal power supply will not work as this would not allow to put data on the same physical wire together with the power.Īnd please note, that depending on the devices, not all devices can be programmed by the miniserver (as programming interface) as the miniserver seems not to fully comply with the KNX standard. As Christian already mentioned, we would need more informations.įor getting the KNX Bus up and running, you will need a "KNX Power Supply" beside the Miniserver on the bus.This (special) KNX Power Supplys creates the electrical KNX Bus environment where all KNX devices (like actors, sensors e.g.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |